Remove backscatter from underwater photos

Remove backscatter from underwater RAW photos in your browser. Find specks proposes every bright particle for review, and you repair the rest in one step.

5 min read Updated Open the editor →

To remove backscatter, open the Heal tab and click Find specks. The editor searches the photo for small bright specks, circles every one it finds, and lets you turn down the ones that aren’t backscatter, such as a fish’s eye or a glint on the sand. Repair then fixes the rest in one step, each with its own heal spot. Specks the finder misses you click by hand.

The finder is experimental. It saves you from clicking hundreds of specks one at a time, but it proposes and you decide: plan to spend a minute reviewing what it found.

OM System TG-7 · ORF Our own dive photo

A turtle shot in shallow water with sun from above. Every bright dot in the water was a particle; the finished edit has them removed.

What backscatter is

Backscatter is light reflected back toward the lens by particles floating in the water: plankton, sand, silt, bubbles. A strobe or a flash lights the particles between the camera and the subject, and so does strong sun in shallow water. Close to the lens they are out of focus and show as soft, round blobs; farther away they are sharp white or colored dots. Against dark open water every one of them shows.

The best fix is at the dive. Aim strobes outward so their beams cross in front of the subject rather than lighting the water in front of the lens, get closer so there is less water to light, and avoid kicking up the bottom. Even with good technique, some backscatter ends up in most wide shots, and that is what this tool is for.

Find and repair specks

  1. Open your photo in the editor and wait until the image has fully loaded: Find specks is available once the full-resolution image is ready.
  2. Open the Heal tab, or press H.
  3. Click Find specks. The search runs in the background; the button reads Searching… meanwhile.
  4. Every candidate is circled in amber. Set Sensitivity so that the specks you can see are circled.
  5. Zoom in and click any circle that isn’t backscatter. It turns into a red circle with a cross and will be left alone. Click it again to bring it back.
  6. Click Repair followed by the number of specks, for example Repair 391. Or click Cancel to leave without changing anything.

OM System TG-7 · ORF Our own dive photo

391 candidates at Sensitivity 30. During review, clicks on the photo only turn candidates down or bring them back; they don't add spots.

The finder works on the decoded RAW, before your adjustments, so changing exposure or color doesn’t change what it finds. You can run it at any point in the edit.

Sensitivity

Sensitivity (0 to 100, default 30) sets how faint a speck may be and still be proposed. At 0 only specks that stand out clearly are circled; at 100 the faintest ones are too, along with more false finds. Changing it doesn’t search again: it shows more or fewer of the candidates already found, instantly, and keeps the ones you turned down. The panel line counts them, for example “391 of 391 found will be repaired”.

Start at the default. Raise it if specks you can see at 100% zoom aren’t circled; lower it if the circles start landing on texture in the subject.

What a repair does

OM System TG-7 · ORF Our own dive photo

Each accepted speck becomes an ordinary heal spot, sized to cover the speck and its soft halo, with a clean source patch picked nearby. The spots use Heal mode at full opacity, with the panel’s current Feather. All of them are added as one step in history, so a single Ctrl Z removes them all.

Because they are ordinary spots, you can fix any single repair afterwards: select it, drag its source, click New source, or press Delete. The heal and clone page explains these controls.

OM System TG-7 · ORF Our own dive photo

After Repair, each repaired speck is a heal spot, marked with a small white circle while the Heal tool is open.

You can run Find specks again after a repair. Specks already under a spot are left out of the new results, so a second pass at a higher sensitivity shows only what is left.

A full-resolution crop of open water above the turtle's shell: before, many bright specks of different sizes; after, the larger and brighter specks are gone and only fine grain-sized dots remain (after)
A full-resolution crop of open water above the turtle's shell: before, many bright specks of different sizes; after, the larger and brighter specks are gone and only fine grain-sized dots remain (before)

OM System TG-7 · ORF Our own dive photo

A full-resolution crop. The larger and brighter specks are repaired; the faintest dots, below Sensitivity 30, and the specks inside the sunburst at the top remain.

If the edit has any masks, a Search menu appears above Find specks. It offers Whole image, and Inside or Outside each mask by name. A speck counts as inside when the mask covers its centre at half strength or more.

Two ways to use it:

  • Protect the subject. Add a brush mask, paint over the animal (its sliders can stay at 0, so it changes nothing in the picture), then choose Outside that mask.
  • Clean only the water. Add a mask over the open water, such as a linear gradient from the surface down, and choose Inside it. A busy reef below then stays out of the search.

Limits of the finder

What the finder looks for, and therefore what it misses:

  • Only bright specks. It finds small spots brighter than their surroundings. Dark specks, such as sensor dust on a bright background, are not found; click them with the heal tool.
  • Only small, round ones. Specks up to roughly 70 pixels across at full resolution are found. Larger, out-of-focus blobs close to the lens are not; repair them with a single click at a larger Size.
  • No streaks. Particles that moved during the exposure show as short lines, which the finder deliberately rejects so it doesn’t pick up fins, rims and edges. Drag a heal stroke along each one.
  • Not in bright areas. Specks on nearly white surroundings, such as a sunburst or blown surface, are skipped.
  • False finds on texture. Eyes, glints, coral polyps, sand grains and bright scales can look like specks. Turn them down, or exclude the subject with a mask.
  • One repair per speck. In dense backscatter where specks overlap a subject’s detail, a repair can soften that detail. Check faces and eyes after the repair and delete any spot that hurts.

At most 2,000 candidates are listed per search, strongest first.

Workflow for a dive photo

  1. Set white balance first: see white balance for the channel gains that bring back reds.
  2. Add a brush mask over the subject if it has eyes or sparkle.
  3. Run Find specks, search Outside that mask, review at 100% and repair.
  4. Search again with a higher Sensitivity if specks remain, then click the last few by hand.
  5. Finish with contrast, Dehaze and color. Repairs stay correct when you change these.